Fig.11 Rubber Dam Clamp for Upper Right and Lower Left Molars
The Fig.11 Rubber Dam Clamp is a stainless steel isolation clamp with flat winged jaws shaped for the diagonal pairing of upper right and lower left molars, acting as the mirror-image partner of the Fig.10. The asymmetric jaw profile follows the mesiodistal curvature of those teeth so the clamp seats evenly on the cervical area, while lateral wings lift the rubber dam away from the tooth to keep the operative field clear. Equate Instruments machines this clamp from surgical-grade stainless steel so it retains spring tension through repeated autoclaving. The bow is drilled with two holes for a standard rubber dam clamp forceps and is supplied non-sterile for routine in-clinic reprocessing.
Specifications
MaterialStainless SteelRusting PreventionPassivatedUltrasonic CleanedYesUsageLeft Hand or Right HandSterileNoReusableYesTests PerformedShape Test, Boil Test and Performance TestLatex FreeYesPackingIndividually PackedQc PassedYesRelated Products
Rubber Dam Clamp Fig. 14 - Festooned Molar Jaws
The Rubber Dam Clamp Fig. 14 from Equate Instruments is a festooned-jaw molar clamp for partially erupted or undersized molar teeth. The gently scalloped jaws follow the uneven cervical contour of such teeth, giving four active points of contact below the height of contour so the clamp does not slide off during isolation. Double forceps-engagement holes accept standard Brewer or straight clamp forceps, and the bow is tall enough to hold the rubber dam well clear of the operative field. Commonly used on maxillary molars within the Ivory universal numbering system, the clamp is machined from hardened stainless steel and is fully autoclavable for in-clinic sterilisation.
View
Rubber Dam Clamp Fig. 14A - Festooned Jaws, Larger Size
The Rubber Dam Clamp Fig. 14A from Equate Instruments is the larger-jaw variant of the Fig. 14 festooned clamp, for partially erupted or undersized molars where a slightly wider grip is required. The gently scalloped jaws follow the uneven cervical contour of these teeth and offer four active contact points below the height of contour so the clamp stays stable under the tension of the rubber dam. Double forceps-engagement holes accept standard Brewer or straight clamp forceps, and the tall bow keeps the dam clear of the working field. It is machined from hardened stainless steel and is fully autoclavable, supplied non-sterile for standard in-clinic sterilisation alongside the rest of the clamp selection.
View
Fig.28 Flat Jaws Molar Rubber Dam Clamp
The Fig.28 molar rubber dam clamp is a winged stainless-steel clamp designed to anchor a rubber dam on the molar dentition. Flat cheek jaws seat below the height of contour on the buccal and lingual surfaces, while the arched bow holds the dam clear of the occlusal table to preserve an unobstructed operating field. The jaw is stamped 28 for rapid identification in a mixed-clamp tray. Crafted from tempered stainless steel, this clamp from Equate Instruments retains its spring tension through repeated steam sterilisation cycles. It is supplied non-sterile and is intended for reuse across restorative, endodontic, and cosmetic procedures on upper or lower molars.
View
Fig.201 Festooned Jaws Rubber Dam Clamp for Upper Molars
The Fig.201 rubber dam clamp is a festooned stainless-steel clamp for upper molars at tooth positions 1-3 and 14-16. The jaws are scalloped to follow the cervical anatomy of maxillary molars, and gingival wings seat below the height of contour to retain the rubber dam without rocking during operative work. The jaw is stamped 201 for rapid identification. Tempered from a single piece of stainless steel, the clamp from Equate Instruments preserves consistent spring tension across repeated steam sterilisation. It is supplied non-sterile and is a routine choice for maxillary molar isolation during restorative, endodontic, and adhesive appointments.
View
Fig.205 Festooned Jaws Rubber Dam Clamp for Large Upper Molars
The Fig.205 rubber dam clamp is a festooned stainless-steel clamp sized for large upper molars at tooth positions 1-3 and 14-16. The scalloped jaw outline follows the cervical anatomy of maxillary molars, and gingival wings seat below the height of contour to retain the rubber dam through the full length of a restorative or endodontic appointment. The jaw is stamped 205 for rapid identification. Tempered stainless steel from Equate Instruments retains spring tension through repeated steam sterilisation. The clamp is supplied non-sterile and is intended for reuse across adhesive, endodontic, and cosmetic procedures on the maxillary arch.
View
Fig.26N Flat Jaws Rubber Dam Clamp for Upper Molars
The Fig.26N rubber dam clamp is a stainless-steel upper molar clamp with flat jaws for tooth positions 16, 17, 26, and 27 in the FDI numbering. The jaw has a narrow, low-profile cheek outline that seats cleanly on the cervical surface of maxillary first and second molars. The arched bow holds the rubber dam clear of the occlusal table throughout operative work, and the jaw is stamped 26N for rapid identification. Tempered from a single piece of stainless steel, this clamp from Equate Instruments preserves spring tension through repeated steam sterilisation. It is supplied non-sterile and is intended for reuse during restorative, endodontic, and adhesive procedures on upper molars.
View
Upper Molar Rubber Dam Clamp #4
An upper molar rubber dam clamp supplied in the Ivory numbering system, designed to anchor the rubber dam around a maxillary molar during operative and endodontic procedures. The wingless, four-prong jaw engages both buccal and palatal aspects of the tooth to deliver stable isolation while leaving the occlusal field clear for instrumentation. Equate Instruments manufactures the clamp from spring-tempered stainless steel so the bow retains its memory across repeated sterilisation cycles. Fully autoclavable and supplied non-sterile for routine in-office processing.
View
Upper Molar Rubber Dam Clamp #5
An upper molar rubber dam clamp supplied in the Ivory numbering system, designed to anchor the rubber dam around a maxillary molar during operative and endodontic procedures. The wingless, four-prong jaw engages both buccal and palatal aspects of the tooth to deliver stable isolation while leaving the occlusal field clear for instrumentation. Equate Instruments manufactures the clamp from spring-tempered stainless steel so the bow retains its memory across repeated sterilisation cycles. Fully autoclavable and supplied non-sterile for routine in-office processing.
View
Fig.8 Festooned Jaws Rubber Dam Clamp for Upper Molars
The Fig.8 rubber dam clamp is a general-purpose festooned clamp for upper molars at tooth positions 1-3 and 14-16 in universal numbering. The scalloped jaws follow the gum curvature of the maxillary molar, and gingival wings seat below the height of contour to retain the rubber dam without rocking on the cervical surface. The jaw is stamped 8 for rapid identification in a mixed-clamp tray. Tempered from a single piece of stainless steel, this clamp from Equate Instruments holds consistent spring tension across steam sterilisation cycles. It is supplied non-sterile and is a routine choice for maxillary molar isolation during restorative, endodontic, and adhesive procedures.
View
Fig.W4 Wingless Flat Narrow Jaws Rubber Dam Clamp for Small Upper Molars
The Fig.W4 rubber dam clamp is a wingless stainless-steel clamp with narrow flat jaws sized for small upper molars at tooth positions 1-3 and 14-16. Without gingival wings, the cheek outline remains compact against the cervical surface, minimising soft-tissue displacement during isolation. The jaw is stamped W4 for rapid identification. Tempered stainless steel from Equate Instruments preserves spring tension through repeated steam sterilisation cycles. The clamp is supplied non-sterile and is a routine choice for maxillary molar isolation during restorative, endodontic, and adhesive procedures where a wingless profile is preferred.
View
Fig.18 Rubber Dam Clamp for Upper and Lower Molars
The Fig.18 Rubber Dam Clamp is a stainless steel isolation clamp engineered to anchor a rubber dam sheet over molar teeth during restorative and endodontic treatment. Its winged, flat round-shaped jaws cradle the cervical area of the tooth while the lateral wings lift the dam away from the operative field for clearer access. The bow is stamped with the figure number and drilled with two holes that accept a standard rubber dam clamp forceps, enabling confident single-handed seating and removal. Equate Instruments machines this clamp from surgical-grade stainless steel that retains spring tension through repeated steam sterilisation cycles. Supplied non-sterile for routine in-clinic reprocessing alongside the rest of the rubber dam kit.
View
Fig.24 Rubber Dam Clamp for Upper Right and Lower Left Molars
The Fig.24 Rubber Dam Clamp is a stainless steel isolation clamp designed for the diagonal pairing of upper right and lower left molars, where the mesiodistal contour demands an asymmetric jaw shape. Its winged flat jaws seat on the cervical area of the tooth while the lateral wings tent the rubber dam away from the operative field. The bow is drilled with two holes for a standard rubber dam clamp forceps, supporting confident single-handed placement and removal. Equate Instruments machines this clamp from surgical-grade stainless steel that retains spring tension through repeated steam sterilisation cycles. Supplied non-sterile for routine in-clinic reprocessing alongside the rest of the rubber dam kit.
View
